Feeds:
Posts
Comments

Posts Tagged ‘Double-Double-End Balls’

My “Do It Yourself” (DIY) efforts on setting up a home workout station are proceeding.  Below are some images of the yesterday’s progress…
Yesterday, I assembled my “double-double”.  Basically, it’s two striking targets attached at two ends.  The bottom target is roughly the height of a body shot (waist to lower ribs).  The top target is roughly the height for head shots (chin, front and side of the head).  You may notice a few things:
1)  the top attachment is vertical while the bottom is horizontal.  The bottom target would normally be either fixed to the flooring below or (using some type of rope or bungee) attached to a weight to stabilize the target and limit random / excessive swinging movement.  In this case, I had to work within the “command structure” of:  “I don’t want any of your weights damaging my concrete!”  So, I used a horizontal bungee (with a loop to keep the rope from sliding left and right).  The practical limitation to this setup is I cannot work around the target;  I am limited to the 180° on the front side.  Still, I can live with it…
2)  less obvious until you start hitting the targets…  They are not “fixed” within the netting.  There are gaps above and below the balls where they can move when struck.  The practical effect of this is they are not staying in the same place in the netting when you try to do a double-up punch (like two jabs to the head).  I will try to correct this by tying rope / paracord around one end of each ball / net to “lock” them into a more standard position within each net.
3)  FAR less obvious, (but which I have learned from recent experience,) is that these targets hit back at you – and from unexpected angles (at least up to now unexpected).  In my initial setup (prior to my wife’s objection), I had the bottom ball / net secured by weights.  This tended to produce reaction motion for both balls in a relatively circular motion around a vertical axis (much like an up-right cylinder).  After the modification to the bottom to include the horizontal bungee, a solid right punch to the bottom target resulted in a solid left hook by the upper ball to the right side of MY head.  My wife started laughing and said:  “It hits back!!”  (Note: NotAre you okay, dear?“)  As near as I can tell, this is due to the back and forth (back to front) motion of the lower horizontal bungee and the circular (like a vertical cylinder) motion of the upper vertical bungee.  My response:  “I’m gonna need a head-guard.”  Her reply:  “You sure are!“, still giggling.  Fortunately (for me), there wasn’t sufficient mass / speed in the basketball to knock me out, because it certainly struck me full on the side of my head at roughly temple / cheek height.
My next brilliant (okay, obvious) idea was to attach the original horizontal double-end target (“bag”) and see what that felt like.  To my surprise, a “triple-double” and it is terrific!  I now had a target (the bottom ball) for body shots, a target (the middle ball) for upper-cuts and body jabs, and a top target (the top ball) for chin and head shots.  The only trick now is to find a way to attach the original double-end to the double-double which keeps them together (when used together), but which also easily separates so I can continue to use the single-double on its own.  The original horizontal “single-double” works as a “slip-rope”.  A “slip” is when you move your head side to side (like a metronome) to avoid an incoming punch.  It is frequently accompanied by a “bob” (up and down head movement).  Together, they are referred to as “bobbing and weaving”.  Basically, I stand next to one post and move to the other ducking under the rope with each step to the side.  When I get to the middle, I release an upper-cut.  I then continue to the opposite post.  When I reach the post, I turn around and start back, trying to time the steps so my next upper cut with be with the other hand.  (Always try to practice every punch with both hands.)  Anyway, there is still some tweaking to do…
The next image is what’s happening in the background.  I attached a “hook-screw” to the back post and then I just swing the weighted chain up to it and hook onto it.  The lat-pulley set up is then out of the way for the boxing.  It is adjustable for more clearance, but because of the angles, it (the chained weights) doesn’t have to be as far back as I initially expected.
And, finally, here’s an image of the “normal” lat-pulldown.  We timed the set up and take down and it takes under a minute to set up or take down!  It takes longer to put on a single boxing hand-wrap than it does to set up the station for boxing.
And so the adventure continues…
.
On This Day In:
2020 Posting As A Continual Exercise
2019 Border Security – Yes, Border Wall – No
2018 Supporting Survival Values
2017 Inauguration Day 2017 [Sometimes, I hate it when I’m right! — KMAB]
2016 Or A Pot Of Gold After The Storm
2015 One, Two, Three…
2014 Lend Your Hand
2013 Amnesty, n.
2012 Best Resolv’d
The Clock Is Running
2011 Magic

Read Full Post »

%d bloggers like this: